high quality horizontal type fluidizing bed drying for WDG line
Description
high quality horizontal type fluidizing bed drying for WDG line is also called fluid bed. Through operation and improvement over 30
years, it has play an active part in the fields of pharmaceutical,
chemical, foodstuff, gain and so on industries. It consists of air
filter, fluid bed, cyclone separator, dust collector, high-speed
centrifugal fan, control cabinet and so on. Because of the
difference of property from raw material, it is necessary to equip
dust remover in accordance with practical needs. It may select
cyclone separator and dust collector both or one of them. In
general, cyclone separator can be selected if the raw material is
larger and the dust collector may be selected if the raw material
is light. Moreover, there is pneumatic feeding device for your
selection. There are two kinds of operation for this machine,
continuous and intermittent type.
sketch flow for model A sketch flow for model B(inner bag type)
sketch flow for model C
(bag filter A manul,B pluse)
Application
Drying process of medicines, chemical raw material, foodstuff,
grain processing, feed and so on. For example, raw medicine,
tablet, Chinese medicine, foodstuff of health protection, drinks,
feed, resin, citric acid and other powders. The suitable diameter
of raw material is normally 0.1-0.6mm. The most applicable diameter
of raw material will be 0.5-3mm.
Working principle
The clean and hot air enters into fluid bed through distributor of
valve plate. The wet material is fed from the feeder forms the
fluid state by hot air. Because of the wide contact between hot air
and raw materials, the time of drying is short. If use continuous
type, the material enters from the front of bed, fluidized in bed
for several minutes, and float another side of bed. The machine’
works in negative pressure.
Technical Parameters
| Model | XF0.25-1(XF10) | XF0.25-2(XF20) | XF0.25-3(XF30) | XF0.25-6 | XF0.3-2 | XF0.3-4 | XF0.3-6 | XF0.3-8 | XF0.3-10 | XF0.4-4 | XF0.4-6 |
| Area of bed layer(m2) | 0.25 | 0.5 | 1.0 | 1.5 | 0.6 | 1.2 | 1.8 | 2.4 | 3.0 | 1.6 | 2.4 |
| Drying capacity(kgh2o/h) | 10-15 | 20-25 | 30-45 | 52-75 | -30 | 42-60 | 63-90 | 84-120 | 105-150 | 56-80 | 84-120 |
| Power of fan(kw) | 5.5 | 7.5 | 15 | 22 | 7.5 | 15 | 22 | 30 | 30 | 30 | 37 |
| Temperature of air in(℃) | 120-140 | 120-140 | 120-140 | 120-140 | 120-140 | 120-140 | 120-140 | 120-140 | 120-140 | 120-140 | 120-140 |
| Tem. of raw material(℃) | 40-60 | 40-60 | 40-60 | 40-60 | 40-60 | 40-60 | 40-60 | 40-60 | 40-60 | 40-60 | 40-60 |
Overall dimensions (main frame)L×W×H(m) | 1×0.6×3.35 | 2×0.6×3.35 | 4×0.6×3.35 | 6×0.6×3.35 | 2×0.70×3.4 | 4×0.7×3.4 | 6×0.7×3.4 | 8×0.7×3.4 |
10×0.7×3.4 |
4×1×3.58 |
6×1×3.58 |
| Occupied area(m2) | 18 | 25 | 35 | 40 | 25 | 38 | 45 | 56 | 70 | 18 | 56 |
| Model | XF0.5-4 (XF50) | XF0.5-6 | XF0.5-8 | XF0.5-10 | XF0.5-12 | XF0.5-14 | XF0.5-16 | XF0.5-18 |
| Area of bed layer(m2) | 2.0 | 3.0 | 4.0 | 5.0 | 6.0 | 7.0 | 8.0 | 9.0 |
| Drying capacity(kgh2o/h) | 70-100 | 105-150 | 140-200 | 175-250 | 210-300 | 245-350 | 280-400 | 315-450 |
| Power of fan(kw) | 30 | 44 | 60 | 90 | 111 | 148 | 169 | 197 |
| Temperature of air in(℃) | 120-140 | 120-140 | 120-140 | 120-140 | 120-140 | 120-140 | 120-140 | 120-140 |
| Tem. of raw material(℃) | 40-60 | 40-60 | 40-60 | 40-60 | 40-60 | 40-60 | 40-60 | 40-60 |
Overall dimensions (main frame)L×W×H(m) | 4×1.2×4.1 | 6×1.2×4.1 | 8×1.2×4.1 | 10×1.2×4.1 | 12×1.2×4.1 |
12×1.2×4.1 |
16×1.2×4.1 |
18×1.2×4.1 |
| Occupied area(m2) | 50 | 70 | 82 | 100 | 140 | 180 | 225 | 268 |
NOTE: The drying capacity is measured on the basis of the primary
and final moisture contents of 20% and 5% respectively of drying
plum crystal and air intake temperature at 130 ℃.drying capacity
for other material will be based on the practical drying condition.
