enamel tank double cone rotating vacuum drying equipment for
chemical use
Enamel or titanium tank for special matrial can be choosed.
Principle of Working
enamel tank double cone rotating vacuum drying equipment for
chemical use has double cone rotating tank. Under the state of vacuum inside the
tank, pass steam or hot water into to jacker for heating. The
energy can contact with the damp raw material through the inner
wall. The vaporized steam can be pumped out through vacuum exhaust
pipe when the damp raw material absorbed heat. Because the inner of
tank is in the state of vacuum and the raw material is turned over
all the time caused by the rotating of tank, the dry speed of raw
material is quickened and drying efficiency is raised too and the
purpose of uniform dry can be raised.
Features
When oil is used to heat, use automatic constant temperature
control. It can be used for drying biology products and mine. Its
temperature of operation can be adjusted from 20~200°C and within
±2°C.
Compared with ordinal drier, its heat efficiency will be over 2
times;
The heat is indirect. So the raw material can not be polluted. It
is in conformity with the requirement of GMP. It is easy in washing
and maintenance.
Application
enamel tank double cone rotating vacuum drying equipment for
chemical use is suitable for drying and mixing powder or granule raw material of
pharmaceutical industry, foodstuff industry and chemical industry
and so on. Especially it is suitable for the following raw
materials that have special requirements:
thermal sensitive raw material that can not in high temperature;
raw materials that are easy to be oxidezed or to be dangerous;
raw materials in which the solvent needs to recover and there is
toxic gases;
raw material that have the requirement of containing rather low
content of residue volatized materials;
raw materials that need to mix evenly and fully.
Technical Parameters
| Model | SZG100 | SZG350 | SZG500 | SZG-7500 | SZG1000 | SZG1500 | SZG2000 | SZG3500 | SZG5000 |
| Volume (litre) | 100L | 350L | 500L | 750 | 1000L | 1500L | 2000L | 3500 | 5000 |
| Charging volume (L) | 50 | 175 | 250 | 375 | 500 | 750 | 1000 | 1750 | 2500 |
| Loading weight(kg) | 40 | 120 | 200 | 300 | 400 | 600 | 800 | 1000 | 1800 |
| Heating area(m2) | 1.16 | 1.5 | 2 | 2.63 | 3.5 | 4.61 | 5.58 | 7.5 | 13.8 |
| Rotating speed(rpm) | 3~13 |
| Motor power | 0.75 | 1.1 | 1.5 | 2.2 | 3 | 4 | 5.5 | 7.5 | 15 |
| Rotating height | 1750 | 2100 | 2250 | 2490 | 2800 | 2940 | 2990 | 3490 | 4200 |
| Desigh pressure insider the tank: ---0.1~0.15Mpa |
| Desigh pressure inside the jacket: ≤0.3Mpr |
| Total weight (Kg) | 650 | 900 | 1200 | 1450 | 1970 | 2280 | 2500 | 2700 | 2900 |
Notes : 1. The above-mentioned parameters are calculated based on
material density 0.6g./cm3.if for reference only.
2. For raw material, if its volume has great change before and
after dry, then its filling coefficient may be increased or
decreased suitably.
3. Speed adjusting motor of 0~6rpm for optional according to user’s
requirement.
The following aspects should be point when order
If certificate for pressure vessel is requirement, please point
out.
if glass lining for interior surface is requirement, please point
out.
If the material is explosive, or flammable, the calculation should
be made according to trial result.1. If material has larger
specific weight, it shall be noted upon placing the order.
